I had a vision in my mind about what type of headboard I wanted for little punk’s room… and I wasn’t stopping until I had it! This headboard was quite the project, but I would definitely do it again…the reward is worth it!
I scoured Pinterest, and the internet in general, for a DIY and found this one to be the most in-depth and useful. Her details were awesome! My design was much different so I had to improvise, but the general knowledge from her tutorial was priceless.
Here’s how I made mine:
I drew my template onto craft paper. You’ll see here I only drew one side…
Then folded it over and cut it out on the line, so it stayed straight and symmetrical
Cut out the template and traced it onto plywood, then let hubs cut it out with some sort of saw.
Next, I purchased 2” upholstery foam from Joann’s (use a coupon…that stuff is expensive!) and cut it to the shape of my plywood and spray glued it in place.
Sorry, my lines are dull in this picture and I changed to highlighter to mark them after a while, but basically, I drew lines every 8” horizontally and vertically. This was probably the most time consuming part for me. Once you have all your lines (straight!) then you make a mark right in the middle of the boxes that were created when you made the lines. This mark will be the diamond part of the tuft
After drilling each hole at the intersection and diagonal mark with a drill bit, you have to use some sort of device (we used the end of a sprinkler head where the threads are for sharpness) to make the 1” cut outs for the buttons to sink into
Speaking of buttons, I covered 54 of these suckers… the thumb hurt that night!
Here is my first button going in!! I was scared… I procrastinated for days before doing this step, but after we got it in, it was smooth sailing…
I convinced hubs this would be a perfect activity for us one night when we were kid-free and football was on the tube. You definitely need help with this step. To tuft the whole thing took the both of us about 2.5 hours to complete
Staple the back and leave a date so when you pull it off the wall years from now you can say “Wow…it was that long ago when we did that!”
There it is ready to go… we used this to hang it. I bought it and hubs was skeptical, but he was amazed at how sturdy and easy it was to hang
What do you think?
You gonna make one?
I priced these online and they range from $500-$1200. I tallied our bill at about $100 plus some elbow grease…
But, we get to say… “We made it” & That makes it all worth it!
Click HERE to see a tour of the completed room!
37 comments:
It's beautiful! What kind of fabric did you use? I'm not sure I understand what you mean about drilling the holes. You used a drill right?
I would like to know the same thing...what fabric and about the drilling of the foam? It turned out so beautiful. I do the same thing sometimes when I get to a certain part of a project that can make it or break it ....I let it sit and make sure that what I am about to do is not going to mess it all up!
Chamorritamom
www.alwaystrying2try.blogspot.com/
great job - - we've used that hanger thing too, on a giant mirror - my husband was also a little skeptical, but it really worked great and was easy to do!
AMAZING!!! I've been wanting to do the same thing for my little one's big girl room (that is when I finally get my rear around to doing it). The way you did it makes so much sense! Seeing this is just what I needed to get me motivated :D
It looks great! Definitely looks like a $1200 headboard, not a $100 headboard!
I used a faux leather type material....it was super cheap ($5/yard) but that was in downtown LA in the fabric district. But saw something similar at Joann's.
Yes, we drilled through the foam and plywood first using a drill bit to make the holes for the button cord to go through. Then after the hole is drilled, you make the bigger hole only through the foam so the button will be inset. Hope that make sense!
Thanks for all the comments!
Gorgeous!!! Also, I just gotta know: where did you get the bedspread and pillow covers? :)
Johanna~ I was lucky enough to find it at Target! Love that place :)
Looks fantastic!!!! :)
That looks amazing. YOU'RE amazing! I love that last pic of little punk :)
Oh yay! I'm so glad you found my tutorial useful, and your headboard looks FABULOUS!!! I absolutely love the shape--very daring and brave for a first time diamond-tufted headboard project, but it turned out great.
wowwwwwwwwwwwwww :)
Wow! You rocked this headboard! It looks fantastic and so desginer...job well done. AD2D does great tutorials, love her blog.
LOVE this!! and the picture too :) how did you get the buttons to stay in place??
Hi , your headboard looks great. I am working on one for my daughter's room. I have a question about how did you make the holes in foam? They look so perfect and clean cut. What kind of tool did you use?
I am almost there where you are ready to make holes in foam, but would like to wait for your reply before starting.
Gagandeep
Hi Gagan, I sent you an email :)
I LOVE your headboard!!! I'm moving in a week and I've purchased my board for the headboard and my fabric (white vinyl) already. I was thinking about doing a nailhead trim, but after looking at this I think I like the tufted look much better.
I was curious about your holes in the foam, what did you use to cut them?
TIA :)
I used a plastic sprinkler extension. It was 1" diameter and had a nice sharp threaded end that help to cut through the foam. Just turn-turn-turn while pushing down and it will cut through. Your wrist all definitely hurt once you're done! Good luck!!
Thanks Susan, can't wait to try it!
Just came across this, and I love it! It looks like you used some batting over the foam, is that right? Did you punch holes into that before putting the buttons in?
Love! Is this a full size? Could you provide me with the dimensions? Do you know if the fabric you used was home dec width like 56" wide? Thanks so much.
orange sugar~ Yes, this is a full size bed I made the headboard for. I just made the dimensions a few inches larger than the bed width-wise and the height is 45" above the top of the mattress...for the full drama effect ;). I think the total height is 48" because we used the entire sheet of plywood and there is still part of the headboard that extends under the mattress... (hope that makes sense!) The fabric I used was 56" home dec size faux leather...very easy to work with!
Hi! I found your post through the link party at Classy Clutter. The headboard looks totally fab, and we actually have the same coverlet on our bed, so you obviously have brilliant taste :o)
I am working on making a tufted ottoman right now, and will probably use a similar process, now if only I could find the perfect fabric.
Lots of Bloggy Love
-Lauren
All I have to say is AMAZING!
Absolutely stunning!!! I recently upholstered a headboard and a bench and yes those covered buttons hurt the thumbs so bad! BUT so worth it! :)
Thanks for linking up on my blog! XOXO!
This headboard came out just gorgeous! I made a tufted ottoman using this method, but I wished I had made the holes in the foam bigger like yours. I was still happy with the results, my next project is a tufted headboard for me. I have been procrastinating to do it, now I feel inspired from the beautiful job you did on yours! Thank you!
This is awesome!!! Didi you put the fabric right onto the foam? I mean no batting? And am I getting this right: the actual holes are 1" in diameter? What's the size of the buttons you used? I'd love to make this, it looks so classy.
I love how you said your husband cut the MDF with "some sort of saw." Funny. The headboard looks great! I made one in December for my mom, using an old ugly wooden headboard I found at a thrift store, but if I were to have started from scratch, I would have shaped mine like yours. Nice work!
Great Job!!! I really want to try making a tufted headboard for my bed.
I have a question, did you stitch the buttons once you had stapled the fabric to the back of the board or did you stitch all the buttons before?
thx!!
Bori~ I emailed you directly
Edi~ By stitching, I'm assuming you mean pulled them through??? I put the fabric over the foam, pulled all the buttons through and then stapled it to the back...hope that helps!
Looks amazing! What size buttons did you use?
From now on I'm in love with your blog! I thought this headboard will be so difficult to do and now it seems to be quite simple ;) Thanks to you!
Thank you for this DIY and have a nice day! :)
Hi Susan :) Love this I am going to try it for my step-daughter's room. We are re-doing it in a pink and zebra theme. Your tutorial is easy to follow I think I may be able to do it :)
Hi Susan, I love your headboard! I bought some similar fabrics and try to make some buttons, but I found it was impossible to cover this kind of thick fabric in to the buttons. I used a hammer, but it didn't work, even the fabric was about to break.
Please~~~~~~~~ tell me how can you made the buttons,.....
I too am having the same problem as Angel. I think it's impossible to make buttons out of faux leather! Is there a trick to it? Also, what size are the buttons you used?
THANKS!
HELLO I TOO WAS HAVING THE SAME PROBLEM WITH THE BUTTONS USING FAUX LEATHER CUT CIRCLE PUSH IN PLACE MAKE 11 CUTS ON EDGE CUT EVERY OTHER FLAP TRIM CORNERS OF REMAINING FLAPS AND THAT IS HOW I GOT IT TO WORK HOPE THIS HELPS:)
Post a Comment
I read each and every comment and look forward to them with every post! I try to respond by email but sometimes things get busy and I just can't. I seriously wish we could all chat and have coffee some day, wouldn't that be fun?. If you do ask a question, I always leave a comment answering. Love ya!